NAS Innovation Mid-range SCSI RAID

 Toll Free-866-482-9837     Telephone-305 463-7517    FAX 305-718-9899

We accept Purchase orders. Check 'pay by check' and fax PO to us.
Choose  product and Configure your custom tower. Price it by adding it to cart and then Purchase it or leave it in cart. The configuration will be saved for you.

All IDE RAID have a three year 24 hour replacement warranty

RAID 0 (striping 2 drive min)

RAID 1 (mirroring even number of drives)

Raid 3 (3 drive min) useable storage=# drives-1 (no hot spare)

Raid 5 (3 drive min hot spare optional) useable storage= #drives-1 drive-hot spare

0+1 (even number of drives) useable storage= #drives/2 (no hot spare)

 The more drive spindles the faster the RAID

More on RAID level defnition
Go back to: Catalog > List of Products
View Cart
Mid-range RAID
Mid-range RAID

Mid-range RAID open
Mid-range RAID open
14 bay base SCSI to SCSI or FIBRE to SCSI RAID system. Mid-range level

$4000.00
Mid-range level 14 bay base RAID system to add SCSI drives to. 80MB SCSI. After third drive you can add empty trays.
RAID level:
Enclosure Type:
Raid Controller:
Drive bay one:
Drive bay two:
Drive bay three:
Drive bay four:
Drive bay five:
Drive bay six:
Drive bay seven:
Drive bay eight:
Drive bay nine:
Drive bay ten:
Drive bay eleven:
Drive bay twelve:
Drive bay thirteen:
Drive bay fourteen:
Interface cable (RAID is 68 pin):
Quantity:
Must add to cart to get final cost and shipping. You can make configuration and cost changes in cart . 
14 bay base mid-range SCSI to SCSI or FIBRE to SCSI RAID systems. Enclosure is fully redundant and hot swap. Check out RAID specifications below.

RAID controller specifications
On-Board CPU
200 MHz Pentium-class, 64 KBytes L1 cache
Host/Device Bus Burst Data Rate: 80MB/s (SCSI host), 80MB/s (SCSI device)

Host Interface
Number Of Channels: One single-ended or Ultra2 (LVD) SCSI
Protocol: Single-ended Narrow (8 bit) or Wide (16 bit); Fast (20 MB/sec), Ultra SCSI (40 MB/sec), or Ultra2 SCSI (80 MB/sec)

Device Interface
Number Of Channels: Two single-ended or Ultra2 SCSI Device Channels
Protocol: Single-ended Narrow (8 bit) or Wide (16 bit); Fast (20 MB/sec), Ultra SCSI (40 MB/sec), or Ultra2 SCSI (80 MB/sec)

Advanced RAID Features
On-line capacity expansion
Spare pooling and dedicated spares; array verification
Hot-swap controller board; global hot-spare; hot-swap devices
Array status monitoring; adjustable stripe width; automatic sector remapping; transparent drive rebuild with user-settable priorities
Arrays can be configured for RAID levels 0, 1, 0/1, 3, 4, 5, 10, and JBOD
Write-through, write-back, and read-ahead cache options

Advanced Hardware Features
Up to 128 MBytes user-configurable, ECC-protected data cache memory
8 Mbytes local Extended Data Out (EDO) DRAM processor memory
Integrated Nickel Metal Hydride (NiMH) cache battery backup interface
Flash upgradable firmware, 2 MBytes

Advanced SCSI Features
Full backward SCSI compatibility
On-board termination, supporting auto multi-mode
70 simultaneous commands; tagged command queuing; disconnect/reconnect
Multiple SCSI Phase EngineTM coprocessors
Reserve/Release (multi-host ready, up to 15 initiators)
Ultra2 SCSI 40 MHz for data transfer up to 80 MB/sec per channel
Up to 15 devices per channel (total of 30 devices)

Configuration And Management
Menu-driven LCD display, channel activity and controller status/fault LEDs, and tactile molded rubber push button controls
RS-232 serial interface to ANSI terminal or terminal emulator for array management
Configuration Application Programming Interface (CAPI) developer's kit
Host SCSI array management and control using CAPI
Programmable SCSI host/device termination and term power
Window-based and menu-based interface
Performance statistic monitoring
Event logging, rebuild and verify utilities
SAF-TE and SMART environmental monitoring support
PC-type lithium disk battery for continuous RTC power

Physical And Environmental Specifications
Board Form Factor: 8.625 in. x 5.75 in (standard 5.25" HDD form factor);
Z-axis height: 1.61 in max
Power Requirements: 235 pin (internal to K5412); 30 watts max (K5412)
Battery backup: Greater than 72 hours
Temperature: 0 degrees C to +45 degrees C operating
-40 degrees C to +100 degrees C non-operating
Humidity: 10% to 85% non-condensing, operating (without battery pack)
5% to 90% non-condensing non-operating (without battery pack)
Air Flow: Non-obstructed intake and exhaust with internal fans